Filter by sub-categories
How to choose a mini digger bucket
- Which bucket for which job. Choose the width by the job, not by the machine: 20 and 30 cm (8" and 12") for cables, water pipes and drainage; 40 and 50 cm (16" and 20") for light footings, manholes and drains; 60 and 80 cm (24" and 32") for earthmoving, grading and loading a trailer; 100 and 120 cm (40" and 48") for levelling and loading loose material. A 1-tonne mini digger works well up to 60 cm, a 1.5 to 2-tonne machine up to 80 cm, a 3 to 4-tonne machine up to 120-150 cm: the wider the bucket, the less breakout force is left.
- Digging, tilt or riddle. The toothed digging bucket is the everyday one: it digs, loads and breaks compacted ground. The tilt ditching bucket tips left and right with a hydraulic ram and is made for cleaning ditches, profiling banks and grading without moving the machine: it connects to the auxiliary hydraulic line on the dipper. The riddle bucket has a barred floor: it picks up stones, roots and rubble and lets the soil fall through, which makes it the bucket for clearing a plot or screening the spoil from a dig. The 90 and 100 cm backhoe buckets are built for tractor-mounted backhoes, but also fit mini diggers with the same dimensions.
- How to tell whether a bucket fits your mini digger. Three dimensions, all at the end of the dipper: the diameter of the two pins (25, 30, 35 or 40 mm), the centres between the dipper pin and the link pin, and the inside width of the hitch, that is the gap the dipper sits in. If the first two match and the bucket's inside width is the same as or slightly wider than the dipper, the bucket fits: the difference is taken up with the shims supplied. Every product page lists the three dimensions. DELEKS® hitches cover six sizes: 25 mm pins at 85 mm centres, in two widths, for 1-tonne minis (the second is the Kubota standard); 30 mm pins at 90 mm centres for 1.5 to 2-tonne machines (the Kubota standard in that class); 30 mm pins at 125 mm centres (the Bobcat standard); 35 mm pins at 153 mm centres for 2.5 to 3-tonne machines; 40 mm pins at 190 mm centres for 3.5 to 4-tonne machines (the Takeuchi, Kubota, JCB and Sany standard in that class). For S30 quick hitches there are buckets with the saddle welded on. If in doubt, the three dimensions and the make of the machine are enough for a definite answer before you order.
- Pins, teeth and thumb. Every bucket comes with its pins; spare pin kits are in stock for all hitch sizes. The teeth are bolted on and are replaced without welding; side teeth widen the cut and protect the cutting edge. The mechanical thumb, fixed to the dipper, turns the bucket into a grab for logs, stones and bulky material: a bucket with a thumb does the job of a grapple on landscaping sites.
- Delivery, warranty and spares. Buckets travel on a pallet by courier; teeth, pins and shims are in stock and ship separately. The warranty covers defects in materials and workmanship; wear of teeth and cutting edge is not a defect. Every product page gives the bucket's weight and capacity, useful also for choosing the trailer that carries the machine.
Frequently asked questions
How do I choose the bucket width?
By the job: 20-30 cm (8-12") for cables and pipes, 40-50 cm (16-20") for light footings and manholes, 60-80 cm (24-32") for earthmoving and loading, 100-150 cm (40-60") for levelling and loading loose material. The maximum width depends on the machine: up to 60 cm for a 1-tonne mini, up to 80 cm for 1.5 to 2 tonnes, wider for machines of 3 tonnes and over.
How do I know whether the bucket fits my mini digger?
Compare three dimensions: pin diameter, pin centres and inside width of the hitch. They are on every product page; with the make and model of your machine we can confirm them before you order.
Do the buckets only fit DELEKS® mini diggers?
No. The hitches match the most common standards: with the same dimensions the bucket fits Kubota, Bobcat, Takeuchi, JCB, Sany and other makes. The dimensions to compare are on the product pages.
Are the pins included?
Yes, with every bucket and every attachment. Spare pin kits are in the same category.
Do you have buckets for the S30 quick hitch?
Yes: the S30 saddle versions have the saddle welded on for the S30 quick hitch.
What do I need to fit a tilt bucket?
An auxiliary hydraulic line on the dipper, the same one used for a breaker. If the machine does not have one, a hydraulic kit can be added: ask before ordering.
What is a riddle bucket for?
For separating stones, roots and rubble from soil: the barred floor lets fine soil fall through and keeps the rest. It is the bucket for preparing a plot, clearing a site or screening spoil.
Can the teeth be changed?
Yes, they are bolted on: they are replaced with a spanner, no welding. Spare teeth are in stock.
How much does a mini digger bucket cost?
Prices are on each product page, with the pallet delivery cost shown in the basket.
What warranty do the buckets have?
Two years on defects in materials and workmanship. Teeth and cutting edge are wear parts.
Français
Deutsch
Română
Русский
Bokmål